Remington Original Part

This is the rivet that holds in the fiber cusion, also called the buffer plate on the Remington model 11 shotgun.

Trigger PIN for No 4 Remington.  This is an ORIGINAL Remington part.

Safety Pin ORIGINAL Remington model 12 and 121. This holds the safety bar in place in the trigger guard.

Remington No. 6 (Type I) Trigger PIN.  

Main Spring SCREW ORIGINAL for No 4 Remington

An ORIGINAL Sear Plunger Cap-SCREW from an early production Remington Model 33.  This screw holds the sear spring and plunger in place.

An ORIGINAL Trigger PIN from a Remington Model 41 and 41P

Screw for the Front RAMP Sight on a Remington Model 700.  This  ORIGINAL screw fits into the tapped holes on the top front of the barrel.

Hammer roll PIN ORIGINAL for No 4 Remington

Extractor spring Remington model 12 ORIGINAL

Firing Pin spring guide Remington model 12 ORIGINAL

hammer bushing Remington model 12 ORIGINAL

An ORIGINAL Trigger SPRING from an early production Remington Model 33

An ORIGINAL Trigger SPRING from an early production Remington Model 41 and 41P.

A carrier dog pin ORIGINAL Remington model 12. This pin goes through the action bar and holds the carrier dog in place.  You can only drive this...

Firing Pin Retractor Mounting Pin Remington model 1-1/2. This is an ORIGINAL Remington part.

Mainspring SCREW Remington model 1. This is an ORIGINAL Remington part.

SCREW for the Safety ORIGINAL on the Remington 510 rifle -

This is the firing spring guide Remington model 12 under serial number approx. 650,000

SPRING for the  Trigger on the Remington 510 rifle - ORIGINAL

carrier dog spring ORIGINAL Remington model 12. This spring sites under the arm of the carrier dog and provides tension to the carrier dog.

This is an ORIGINAL safety plunger Remington model 12 and 121

PIN for the Remington No. 6 (Type I) Hammer.  This pin goes through the receiver and holds the hammer in place.  

Stock bolt ORIGINAL WASHER Remington model 12 and Remington model 121. This fits on the stock bolt and goes inside the stock.

An ORIGINAL Escutcheon for the Take down screw on a Remington Model 33 

PIN Firing Pin on a Remington model 12 ORIGINAL

Butt Plate SCREW Remington model 4 rolling block rifle. This is an ORIGINAL Remington part.

This is an ORIGINAL Forearm Screw for the Remington model 12. This screw secures the wooden pump handle to the slide. There is one on each side of...

Dummy(also called the upper tang plug) SCREW Remington model 4 rolling block rifles. This is an ORIGINAL Remington part and fits into the top of...

Button SCREW Remington model 1. This is an ORIGINAL Remington part.

Front Guard SCREW Remington model 1 ORIGINAL

Sear PIN Remington model 1. This is an ORIGINAL Remington part.

An ORIGINAL Escutcheon for the Take down screw on a Remington Model 41

This is an ORIGINAL Scalloped forearm screw Remington model 12, 12c. The forearm lock screw (rp 2 ) holds the scalloped screw in place. If you would...

Remington 742 hammer spring (mainspring). Used but in excellent condition.

This is the ORIGINAL screw that holds the scalloped forearm screw (rp1, rp61-b) in place on the Remington model 12 and 12c. If you would prefer a new...

Button Remington model 1 - this is the signature part Remington model 1 rifle, and goes on the side of the receiver holding the pins in place trigger...

Extractor RETAINING SCREW for Remington Model 2 ORIGINAL. 

PIN that holds the Firing Pin place for Remington Model 2  ORIGINAL. 

NEW Receiver bushing That is NOT threaded for Remington model 12. 

 Rear sight ELEVATOR SCREW ORIGINAL for  a Remington model 12  and 24 

Tang Screw Remington model 1. This is an ORIGINAL Remington part.

This is the ORIGINAL Buttplate Screw from Remiongton 22  bolt action rifles. This screw was used on models like the 33, 32, 31 and 12B and...

This is the hammer spring (mainspring) ORIGINAL Remington model 12 and 121 rifle. These are ORIGINAL Remington Factory springs that still are in...

An ORIGINAL Take down screw Remington Model 41 or 41P

This is the ORIGINAL safety Remington model 12 or model 121

An ORIGINAL Sear  PLUNGER from an early production Remington Model 33.  This plunger fits into the hole on the end of the sear and has a...

An ORIGINAL Trigger Guard SCREW from an early production Remington Model 33

Tang Screw ORIGINAL for No 4 Remington. This is the screw that attaches through the upper metal tang and holds the stock on the rifle.

Original SCREW for Buttplate on a Remington Model 2 Rolling Block Rifle 

Hammer SCREW ORIGINAL for No 4 Remington

This is the SCREW for the Remington No. 6 Forearm  ORIGINAL  

NEW Receiver BUSHING that is threaded Remington model 12. Fits into right side of the receiver so that the takedown screw  can be attached.

SPRING for the Remington No. 6 (Type I) Hammer.    

This is a factory original magazine spring 12 gauge Remington model 11 shotgun

ORIGINAL Receiver Bushing for the Assembly screw on the Remington Model 12.  This is the threaded bushing.

Ejector SPRING Remington Model 12 ORIGINAL for the earlier production Model 12 rifles

This is the hump back trigger Remington model 11 shotgun. This trigger is guard that utilizes the forward safety.

This is the trigger Remington model 11 shotgun. This trigger is guard that utilizes the forward safety.

SCREW  for the Trigger and Spring ORIGINAL for No 4 Remington

This is the ORIGINAL plunger that goes into the action bar on the Remington model 12 and 121 pump .22. It is held in place by the action bar plunger...

cartridge stop Remington model 12 ORIGINAL

An ORIGINAL PIN for the Firing Pin Catch on a Remington Model 14

An ORIGINAL Firing Pin Catch SPRING for Remington Model 14

An ORIGINAL Elevator for the Remington 500 Series rear sight that is attached with two screws.