Remington Original Part

Firing Pin on a No 4 Remingtonrolling block in 25 caliber.  This firingpin goes through the breech block.

PIN Firing Pin on a Remington model 12 ORIGINAL

Firing Pin Remington model 1. This is an ORIGINAL Remington part.

Remington No. 6 firing pin NEW  

Firing Pin Retractor Mounting Pin Remington model 1-1/2. This is an ORIGINAL Remington part.

Metal Forearm CAP for Remington Model 2  ORIGINAL. 

This is the ORIGINAL screw that holds the scalloped forearm screw (rp1, rp61-b) in place on the Remington model 12 and 12c. If you would prefer a new...

This is an ORIGINAL ribbed forearm with the standard tapered front Remington model 12 pump 22 rifle. It is all complete and ready for installation....

Forearm for Remington Model 2  ORIGINAL. 

Remington No. 6   FOREARM taken from an early Remington No 6 rifle.   This fits Type 1 rifles that have the smaller forearm....

A Forearm ribbed (ORIGINAL) Remington Rifle. Longer length than the model 12 at 8 inches long. Action arm space has been enlarged at the Forearm.

BASE that holds on the  forearm SCREW on the Remington Model 2  ORIGINAL. This base fits into the dovetail on the underside of the...

This is an ORIGINAL Forearm Screw for the Remington model 12. This screw secures the wooden pump handle to the slide. There is one on each side of...

This is the SCREW for the Remington No. 6 Forearm  ORIGINAL  

Front Remington Sporting Sight for the Model 33

An ORIGINAL Guard (trigger) for Remington Model 14.  

Rear Guard SCREW Remington model 1

Hammer ORIGINAL for No 4 Remington rolling block rifle.

Hammer PIN Remington model 1. This is an ORIGINAL Remington part.

PIN for the Remington No. 6 (Type I) Hammer.  This pin goes through the receiver and holds the hammer in place.  

This is an ORIGINAL Hammer Short, Long and Long Rifle for the EARLY (~1909) Remington model 12 pump .22 rifle.  This is a larger (wider) hammer...

This is an ORIGINAL Hammer Short, Long and Long Rifle Remington model 12 pump .22 rifle.  This hammer is the middle one in the picture and this...

Remington No. 6 (Type I) Hammer  

Hammer roll PIN ORIGINAL for No 4 Remington

Firing Pin spring guide Remington model 12 ORIGINAL

This is AN ORIGINAL rod that the mainspring (hammer spring (mainspring)) goes around on the Remington model 12 and 121 pump .22 rifles. This rod is...

This is an ORIGINAL Hammer with a guide rod attached for the  Remington model 12 pump .22 rifle.

Lever Spring Remington model 1. This is an ORIGINAL Remington part.

Locking Lever ORIGINAL for No 4 Remington

Locking Lever PIN Remington model 1. This is an ORIGINAL Remington part.

Locking Lever Stop PIN ORIGINAL for No 4 Remington

This is an ORIGINAL Magazine Hanger (magazine ring), also called magazine ring, or band, Remington model 12A and 121. This is the part that twists...

Release inner magazine tube on a Remington model 12 pump 22 rifle. This ORIGINAL part fits into the inner magazine tube and on the magazine cap--...

magazine screw ORIGINAL Remington model 12

This is the complete inner magazine tube Remington model 121 pump .22 S, L, LR. The tube is complete with follower, spring and plug (with spring and...

This is the outer magazine tube Remington model 121 pump .22 S, L, LR. The tube is 14 1/4 inches long and threaded on one Forearm.

This is AN ORIGINAL outer magazine tube Remington model 12a pump .22 S, L, LR. This is 12a rifle that has the round barrel. The tube is 12 inches...

Main Spring ORIGINAL for No 4 Remington.  This spring has a dual purpose serving as the spring for the hammer and the trigger.

Mainspring Remington model 1. This is an ORIGINAL Remington part.

Mainspring SCREW Remington model 1. This is an ORIGINAL Remington part.

Middle Barrel band for a Remington model 1. This band usually contains the sling swivel, This is a military style , no screw , holded bu a pin onn...

Rear Barrel Band Remington model 1 Military type , no screw hole in band . Held by fore arm pin

ORIGINAL Receiver Bushing NOT THREADED for the Assembly screw for the Remington Model 12.  This is the non-threaded bushing.

ORIGINAL Receiver Bushing for the Assembly screw on the Remington Model 12.  This is the threaded bushing.

An ORIGINAL Receiver Insert PIN for the Remington 510 rifle -  This pin slides into the receiver and holds the receiver insert in place.

This is a original factory replacement recoil spring Remington model 11 16-20 gauge.

Recoil Stud SCREW Remington model 1

Remington 742 hammer spring (mainspring). Used but in excellent condition.

Remington model 11 bronze friction ring 12 GA

Remington Model 700 ORIGINAL gun box

This is the rivet that holds in the fiber cusion, also called the buffer plate on the Remington model 11 shotgun.

Safety Pin ORIGINAL Remington model 12 and 121. This holds the safety bar in place in the trigger guard.

This is an ORIGINAL  Safety Plunger Spring on the Remington model 12 and 121.  This spring fits around the safety plunger (part #...

This is the ORIGINAL safety Remington model 12 or model 121

An ORIGINAL Sear from an early production Remington Model 33

Sear PIN Remington model 1. This is an ORIGINAL Remington part.

A Sear Pivot Screw ORIGINAL for the Remington 510 rifle -

An ORIGINAL Sear  PLUNGER from an early production Remington Model 33.  This plunger fits into the hole on the end of the sear and has a...

A Sear ORIGINAL for the Remington 510 rifle -

Sear for Remington Model 2 ORIGINAL. 

Screw for the Front RAMP Sight on a Remington Model 700.  This  ORIGINAL screw fits into the tapped holes on the top front of the barrel.

This is the ramp for the front sight on a Remington Model 700. The ramp is .26 0 high from barrel to bottom of sight dove tail.  This front...

Number 12 Remington Front sight ORIGINAL for Remington model 12, Model 23, 33, 41 and other 22 rifles. This is a factory ORIGINAL Remington front...

Number 31 Remington Front sight ORIGINAL for Remington 500 model series,  Model 23, 33, 41 and other 22 rifles. This is a factory ORIGINAL...

 rear sight  BASE SCREW , ORIGINAL on a Remington model 12 and 24