Remington Original Part

Hammer pin ORIGINAL (rop) Remington model 12. This pin connects the hammer to the hammer spring (mainspring) rod.

Locking Lever Stop PIN ORIGINAL for No 4 Remington

SCREW for the Remington No. 6 (Type I) breech block SPRING  

This is the PIN for the Remington No. 6 (Type I) Extractor - this is the part that holds the ejector in place underneath the barrel chamber....

Remington No. 6 (Type I) breech block PIN

An ORIGINAL SearPIN from an early production Remington Model 33

An ORIGINAL Trigger PIN from an early production Remington Model 33

Receiver ORIGINAL guide pin for the Remington model 12. These pins fit into the left and right side of the trigger guard top and guide the...

Screw for the Front RAMP Sight on a Remington Model 700.  This  ORIGINAL screw fits into the tapped holes on the top front of the barrel.

This is an ORIGINAL  Safety Plunger Spring on the Remington model 12 and 121.  This spring fits around the safety plunger (part #...

This is the pin that holds the trigger in place on the Remington model 12 and 121 pump .22 rifles. It also fits the 12, 1 1/2 and model 141.

The Ejector Screw ORIGINAL for the Remington 510 rifle -

Recoil Stud SCREW Remington model 1

Plunger for the Trigger Spring on the Remington 510 rifle - ORIGINAL

action bar plunger pin Remington model 12 ORIGINAL

Front Band SCREW Remington model 1

Lever Spring SCREW Remington model 1. This is an ORIGINAL Remington part.

Trigger Spring SCREW Remington model 1. This is an ORIGINAL Remington part.

This is the firing spring guide Remington model 12 under serial number approx. 650,000

SPRING for the  Trigger on the Remington 510 rifle - ORIGINAL

carrier dog spring ORIGINAL Remington model 12. This spring sites under the arm of the carrier dog and provides tension to the carrier dog.

This is an ORIGINAL safety plunger Remington model 12 and 121

An ORIGINAL Barrel PIN for the Remington 510 rifle - .

Locking Lever PIN Remington model 1. This is an ORIGINAL Remington part.

Stock bolt ORIGINAL WASHER Remington model 12 and Remington model 121. This fits on the stock bolt and goes inside the stock.

An ORIGINAL Escutcheon for the Take down screw on a Remington Model 33 

PIN Firing Pin on a Remington model 12 ORIGINAL

An ORIGINAL Sear Plunger SPRING from an early production Remington Model 33.

This is the fiber cushion also called the buffer plate Remington model 11 in 12 and 16 gauge. A rivet (part number R112 holds this piece on.

PLUG Tang Screw ORIGINAL for No 4 Remington. This is the small screw that attaches through the upper metal tang and fills the holefor a tang sight...

Dummy(also called the upper tang plug) SCREW Remington model 4 rolling block rifles. This is an ORIGINAL Remington part and fits into the top of...

Button SCREW Remington model 1. This is an ORIGINAL Remington part.

Front Guard SCREW Remington model 1 ORIGINAL

Sear PIN Remington model 1. This is an ORIGINAL Remington part.

An ORIGINAL Escutcheon for the Take down screw on a Remington Model 41

This is an ORIGINAL Scalloped forearm screw Remington model 12, 12c. The forearm lock screw (rp 2 ) holds the scalloped screw in place. If you would...

Remington 742 hammer spring (mainspring). Used but in excellent condition.

This is the ORIGINAL screw that holds the scalloped forearm screw (rp1, rp61-b) in place on the Remington model 12 and 12c. If you would prefer a new...

Extractor RETAINING SCREW for Remington Model 2 ORIGINAL. 

Mainspring SCREW for Remington Model 2  ORIGINAL. This screw goes inot the underside of the upper tang and holds the mainspring in place.

 rear sight  BASE SCREW , ORIGINAL on a Remington model 12 and 24 

WASHER for the Remington No. 6 (Type I) stock Bolt - this washer prevents ther bolt from runninh through the stock.   

An ORIGINAL Screw for the  Remington Model 14 Action Bar in 35 REM caliber.  

buttplate Screw Remington model 12 ORIGINAL part. This screw that will fit any Remington model 12 buttplate including curved metal on 12B - a new...

An ORIGINAL Take down screw Remington Model 33 

This is a trigger spring plunger case for the Remington model 12 and 121 pump-22 rifle.  This is an ORIGINAL Remington part.

ORIGINAL Receiver Bushing NOT THREADED for the Assembly screw for the Remington Model 12.  This is the non-threaded bushing.

An ORIGINAL Screw for the Remington 500 Series rear sight that is attached with two screws.

An ORIGINAL Trigger Guard SCREW from an early production Remington Model 33

Tang Screw ORIGINAL for No 4 Remington. This is the screw that attaches through the upper metal tang and holds the stock on the rifle.

Forearm SCREW for No 4 Remington  Rolling Block - ORIGINAL -

This is AN ORIGINAL rod that the mainspring (hammer spring (mainspring)) goes around on the Remington model 12 and 121 pump .22 rifles. This rod is...

This is the SCREW for the Remington No. 6 Forearm  ORIGINAL  

NEW Receiver BUSHING that is threaded Remington model 12. Fits into right side of the receiver so that the takedown screw  can be attached.

SPRING for the Remington No. 6 (Type I) Hammer.    

This is a factory original magazine spring 12 gauge Remington model 11 shotgun

ORIGINAL Receiver Bushing for the Assembly screw on the Remington Model 12.  This is the threaded bushing.

Ejector SPRING Remington Model 12 ORIGINAL for the earlier production Model 12 rifles

This is the hump back trigger Remington model 11 shotgun. This trigger is guard that utilizes the forward safety.

This is the trigger Remington model 11 shotgun. This trigger is guard that utilizes the forward safety.

Breech Block Screw ORIGINAL Remington model 4

This is the ORIGINAL plunger that goes into the action bar on the Remington model 12 and 121 pump .22. It is held in place by the action bar plunger...

cartridge stop Remington model 12 ORIGINAL

An ORIGINAL PIN for the Firing Pin Catch on a Remington Model 14