Remington Original Part

Firing Pin ORIGINAL for No 4 Remington

PIN that holds the Firing Pin place for Remington Model 2  ORIGINAL. 

Firing Pin Retractor Mounting Pin Remington model 1-1/2. This is an ORIGINAL Remington part.

This is an ORIGINAL ribbed forearm with the standard tapered front Remington model 12 pump 22 rifle. It is all complete and ready for installation....

A Forearm ribbed (ORIGINAL) Remington Rifle. Longer length than the model 12 at 8 inches long. Action arm space has been enlarged at the Forearm.

SCREW  that holds on the  forearm on the Remington Model 2  ORIGINAL. 

An ORIGINAL Guard (trigger) for Remington Model 14.  

PIN that holds the Hammer in place for Remington Model 2  ORIGINAL. 

Hammer Remington model 1 This is an ORIGINAL Remington part.

ROLL for the Hammer on a No 4 Remington  ORIGINAL

Locking Lever ORIGINAL for No 4 Remington

Locking Lever Recepticle NUT for the No 4 Remington Rolling Block Rifle.  This very rare piece fits into the side of the receiver and the...

Main Spring SCREW ORIGINAL for No 4 Remington

Rear Barrel Band Remington model 1 Military type , no screw hole in band . Held by fore arm pin

An ORIGINAL Receiver Insert for the Remington 510 rifle -  This part slides into the receiver and is held in place by pins.

Remington 511 TRIGGER ORIGINAL

Lever for the Safety ORIGINAL on the Remington 510 rifle -

SCREW for the Safety ORIGINAL on the Remington 510 rifle -

Sear PIN for Remington Model 2 ORIGINAL. 

An ORIGINAL Sear  PLUNGER from an early production Remington Model 33.  This plunger fits into the hole on the end of the sear and has a...

Stud ORIGINAL for the Sear fon a Remington 510 rifle -

Remington Front Sight ORIGINAL from a .22 rifle with wear on the blade. Dove tail sides still strong. Blade clean and a little lower than the No 28...

Sight Rear ORIGINAL from an early rolling block rifle. This fixed rear sight, with V sighting notch, fits into a 0.435 inch dovetail. This sight is...

Sight Rear ORIGINAL Remington 701 1/2 used on .22 bolt action rifles.

Rear Remington  Sight for the Model 33

An EXCELLENT condition STOCK for the Remington 510 ORIGINAL

Stock ORIGINAL Remington model 4 rolling block in EXCELLENT condition. Escutcheon in wood for tang screw. No cracks in wood, a few handling marks and...

Stock Bolt ORIGINAL for the Remington 510 rifle -  This bolt holds the stock onto the metal barrel and receiver.

PLUG Tang Screw ORIGINAL for No 4 Remington. This is the small screw that attaches through the upper metal tang and fills the holefor a tang sight...

PIN for the Trigger and Block Spring on a Remington Model 2 in 32 caliber ORIGINAL. This pin spans and holds the spring into the lower tang.

An ORIGINAL Trigger for the Remington Model 14.  

Trigger GUARD (lower Tang) for Remington Model 2 ORIGINAL. This items comes stripped and does not contain the trigger and spring.

Trigger ORIGINAL for No 4 Remington rolling block rifle.

An EXCELLENT Trigger ORIGINAL for the Remington 510 rifle -

An ORIGINAL Trigger SPRING from an early production Remington Model 33

An ORIGINAL Remington Model 14 Action Bar Cover for 35 REM caliber.  

This is the ORIGINAL plunger that goes into the action bar on the Remington model 12 and 121 pump .22. It is held in place by the action bar plunger...

ORIGINAL Barrel Band for the Remington Model 4 rolling block Boy Scout rifle.  In Excellent condition.  Screw is still in hole on...

Barrel from a Remington model 1 in MODERATE condition. Still with original bluing but with some older pitting. Bore on this in 43 Spanish Remington...

Barrel in MODERATE condition 12A rifle. These are used original Remington model 12A round barrels in M = MODERATE condition. Bores still with rifling...

Barrel in GOOD condition rifle. These are used original Remington octagon model 12B barrels in G = GOOD condition. Bores still with strong rifling...

Barrel .22 caliber for the Remington model 4 rolling block ORIGINAL in Excellent condition. A large amount of cover remaining on the metal. Screw...

Barrel in 22 LR for the Model 44 rolling block rifle. This is a thick bull barrel with original bluing, clear stamping of Stevens origin in the...

Bolt / Breechblock Remington model 12 ORIGINAL that utilizes a Round firing pin.Breech block  fits in rifles with serial numbers above 650,000...

Bolt / Breechblock STRIPPED Remington model 12 ORIGINAL that utilizes a Round firing pin.Breech block  fits in rifles with serial numbers above...

SALE-----This is an original bolt Remington model 11 shotgun. It is a 12 gauge stripped bolt that uses the square firing pin

A very rare ORIGINAL Bolt for the Remington early production Model 33

Remington No. 6 (Type I) breech block Lever - this is used to rais3e and lowere the breech block.

PIN that holds the Breech Block in place for Remington Model 2  ORIGINAL. 

Breech Block for the Remington Model 4 Rolling Block 25 ORIGINAL

Breech Block Screw ORIGINAL Remington model 4

SCREW for the Remington No. 6 (Type I) breech block SPRING  

Button for Remington Model 2  ORIGINAL. This holds the hammer and breech block pin from falling out of the receiver.

Remington No. 6 (Type I) Metal Buttplate.  This ORIGINAL buttplate has a slight curve backwards on the top portion and has the...

Metal Buttplate ORIGINAL for Remington Model 2 Rolling Block Rifle

This is the ORIGINAL Buttplate Screw from Remiongton 22 single-shot and bolt action rifles. This screw was used on models like the 12, 33, 32,...

This Is the carrier Remington model 11 shotgun. This is the 20 gauge carrier.

Initial Carrier (First Variation) earliest Remington model 12 rifles (rp51 rop). This is an ORIGINAL part early guns that take the first carrier...

cartridge retainer Remington model 12 ORIGINAL

An ORIGINAL Escutcheon for the Take down screw on a Remington Model 41

Extractor plunger Remington model 12 ORIGINAL

This is the extractor Remington model 12 pump .22

Extractor for Remington Model 2 ORIGINAL. 

Extractor RETAINING SCREW for Remington Model 2 ORIGINAL. 

This is the fiber cushion also called the buffer plate Remington model 11 in 12 and 16 gauge. A rivet (part number R112 holds this piece on.