Winchester Original Part

This is the magazine band bushing Winchester model 12. 16/20 gauge. This bushing slides through the middle of the magazine band and the bushing...

This is the magazine band bushing Winchester model 12. 12 gauge. This bushing slides through the middle of the magazine band and the bushing screws...

Magazine band  --12 ga-- Winchester 1897

Magazine (Carrier) Throat Pin ORIGINAL Winchester model 72

This is the lower tang Winchester 94 POST 64 ANGLE eject model. It is blued and does not come with any of the other components ie trigger, springs...

A NEW reproduction Lower tang Screw Winchester 1885 High Wall

This is the COMPLETE lower tang Winchester 94 POST 64 TOP  eject rifle  HAMMER. TRIGGER, SAFETY BAR, SAFETY BAR PIN, MAINSPRING, ASSISTING...

Lower Barrel Band SCREW for a Winchester 1895 Lee Straight Pull rifle ORIGINAL

This is the ORIGINAL locking bolt Winchester 1894, model 64 and 55 lever action rifles. This part moves up behind the bolt to lock it in battery....

This is the RIGHT side ORIGINAL locking bolt Winchester 1892 lever action rifle. This part sits in grooves in the receiver on the right side (Loading...

This is an ORIGINAL locking bolt pin Winchester 1892, model 65 and 53. This pin connects the left and right locking bolts with the finger lever. It...

This is an ORIGINAL PAIR of  locking bolts Winchester 1886 rifle and model 71. Both Left and Right sides that lock the breech bolt into...

This is the LEFT side (non Loading gate (spring cover side) ORIGINAL locking bolt Winchester 1886 rifle and model 71. Both Left and Right sides...

This is an ORIGINAL complete locking bolt for a side eject POST-64 Winchester 94. The bolt comes with the firing pin striker and firing pin...

Locking Bolt Assembly COMPLETE with Cartridge Stop and two pins, for the LATER PRODUCTION PERIOD (usually after serial number 70,000) Winchester...

Locking Bolt Assembly COMPLETE with Cartridge Stop and two pins, for the LATE (usually AFTER serial number 70,000) Winchester 1895.  THIS FITS...

Locking Bolt Assembly STRIPPED without Cartridge Stop and two pins.  Will fit into all caliber Winchester rifles and with all types of 1895...

This is an ORIGINAL locking bolt for the pre 64 Winchester 1894 and Model 64 and Model 55 . It is .005 oversized to compensate for excessive...

Locking  BLOCK  for WINCHESTER  1911 Model 11  ORIGINAL 

Lock Spring Guide rod stop pin ORIGINAL model 37 Winchester single-shot shotgun. This pin fits ALL gauges except .410 of the model 37 shotgun.

Lock Spring Guide rod ORIGINAL model 37 Winchester single-shot shotgun. This rod fits 1st style model 37 shotguns.

Lock Pin ORIGINAL model 37 Winchester .410 gauge single-shot shotgun.

Lock Pin ORIGINAL model 37 Winchester in 12/16 gauge

Lock ORIGINAL model 37 Winchester 20 or 28 gauge single-shot shotgun.

Lock ORIGINAL 37 Winchester 12 gauge shotgun.

This is the screw that attaches the Loading gate (spring cover) to the receiver of the Winchester model 94 POST 64. It is used with all...

ORIGINAL Spring cover Winchester 94 POST 64 IN 30-30 CAL only. Note: The Loading gate (spring cover) for .357 is part number (c175-a)., 450 marlin,...

This is an ORIGINAL Loading gate (spring cover) cover Winchester 1894, model 64 and model 55 lever action rifles. This Loading gate (spring cover)...

This is the brass plated Loading gate (also called spring cover) for the Winchester POST 64 model 94. The screw that holds the Loading gate...

This is a link POST 64 Winchester 94. It fits rifles above serial number 5,550,001 This link does NOT have the internals, If you need the friction...

This is an ORIGINAL link for a Winchester 1894 and model 64 rifles (pre 64) It has already installed the friction stud, friction stud spring and stop...

This is the link Winchester 94 POST 64 early top ejects.COMPLETE  This link have the internals,  If you are having problems with...

Link Rear PIN Winchester Model 88 ORIGINAL

This is the link pin Winchester 94 POST 64 over serial number 5,500,001. This pin attaches your link to the receiver. The screw that holds this pin...

This is the link pin stop screw Winchester 94 POST 64. It fits rifles with serial number above 5,500,001, It also fits the model 9410 shotgun

Link Front Left Winchester Model 88 ORIGINAL

Link   Rear PIN Winchester Model 88 ORIGINAL

Lever Link Pin long ORIGINAL Winchester 1885 rifle

Knock-off Stop Pin ORIGINAL Winchester 1885 Low Wall rifle. This round pin stops the knock-off from over rotating, and the pin has the middle on one...

Knock-off Spring ORIGINAL Winchester 1885 rifle

Knock-off Spring pin ORIGINAL Winchester 1885 rifle

Knock-off operating pin ORIGINAL Winchester 1885 rifle

This is a ORIGINAL hammer comlete that fits on the Winchester model 1866 and the 1873 lever action rifles. These are NOT reproductions so the finish...

Hammer Winchester Model 88 ORIGINAL

Here is an ORIGINAL used hammer POST-64 Winchester 94 top eject rifle. It looks to have been previously installed on a rifle with minor wear marks...

This is the hammer for  Winchester 94 POST 64 AE (angle eject) rifle. It fits those guns that have a hammer spur extension (part...

This a ORIGINAL hammer Winchester 1894 (pre 64) (not set trigger). Pre-64 1894s that had a standard trigger, used 3 different hammer designs. This...

This a ORIGINAL hammer Winchester 1894 (pre-64) (not set trigger). 1 st STYLE original This part is from a pre-64 Winchester 1894 sporting rifle that...

Hammer Winchester 1200 and 1300 Shotgun 12 gauge

Hammer Stripped -ORIGINAL- Winchester 1897

This is the hammer stirrup Winchester 1866 1873 1876 1886 lever-action rifles and the 1897 and 1893  shotgun. This part attaches to the...

This is the Hammer Stirrup PIN Winchester for the Winchester 1866 1873 1876 1886 1892 and 1894 lever-action rifle. 

Hammer Spring Support Winchester 1200 and 1300 Shotgun 12 gauge.  This plastic disc fits into each side of the hammer spring - two are...

Hammer Spring Guide Rod Winchester Model 88 ORIGINAL

Hammer Spring Guide Rod PIN Winchester Model 88 ORIGINAL

Pin that holds the Winchester 1903 and Model 63 hammer spring abutment into the receiver

Spring that puts tension on the hammer Winchester model 61 .22 cal. This is 61 that shoots the Short, Long or Long Rifle. The magnum .22 uses a...

An ORIGINAL hammer spring (mainspring) for the Winchester 1200 and 1300 shotgun. Fits all 20, 16 and 12 gauge guns.

This is AN ORIGINAL hammer spring (mainspring) guide rod for the Winchester 94 POST 64

This is the guide rod that goes through the hammer spring (mainspring), and attaches to the hammer. This rod is the same for all gauges of the...

This is the hammer spring (mainspring) abutment Winchester model 61

This is an ORIGINAL pin for the hammer spring (mainspring) abutment on the Winchester model 63 and 1903

This is an ORIGINAL hammer spring (mainspring) abutment guide rod. the hammer spring (mainspring) (wp13s) goes around this bar and puts tension on...

This is the screw that holds the hammer in place on the Winchester model 94 POST 64

Hammer Pin Win 1897