Springs and Things

Buttplate Trap door SPRING for the 1866 and the 1st model 38-40 and 44-40 Winchester 1873 Sporting Rifles.  This will not fit the carbine...

Carrier Lever spring ORIGINAL Winchester 1873 (wp165a wop). There are two springs required, one left (Finger Lever) and this carrier lever spring on...

This is the cartridge cut off spring Winchester model 63 and 1903. Even though the cutoff shape is different for both guns, the spring is the same.

This is the ejector spring and the ejector stop spring Winchester model 61.

Extractor 2nd variation for mid-production 1894 Stevens Favorite NEW This type is the center style and is 0.200 inches wide from top to...

This is the UPPER extractor plunger spring Winchester model 61 .22 rifle.

Spring lower extractor on the Winchester model 61 .22 rifle

Finger Lever catch spring ORIGINAL for all Winchester 1873 guns.

This is an ORIGINAL finger lever latch  (also called the finger lever catch) Winchester 1873 2nd and 3rd model. It fits all 1876 model...

This finger lever spring attaches inside on the left of the receiver.(the side with out the Loading gate (spring cover)) This replacement spring...

A NEW eproduction Firing Pin with rounded tip for the later production  Stevens 1915 Favorite. If you have an earlier 1880s model you will need...

Winchester Model 60 and 60A firing pin NEW spring. This spring pushes the firing pin into the 22 cartridgeand fits the single-shot...

This is a NEW  firing for your Stevens favorite.Firing pin with chisel tip for the 1889/1894 Stevens Favorite.

This is the hammer spring (mainspring) abutment Winchester model 61

This is the rod that attaches to the hammer on the Winchester model 61. The coil hammer spring (mainspring) sits around this rod

Spring that puts tension on the hammer Winchester model 61 .22 cal. This is 61 that shoots the WRF (magnum) rounds. If your rifle shoots the short,...

This is the hammer spring (mainspring) guide rod Winchester model 63 and 1903. The coiled hammer spring (mainspring) goes over this part.

Link for the Stevens Favorite - and ORIGINAL Stevens part for the early -production 1889 era Favorites.  This is the smallest type of Favorite...

Link for the Stevens Favorite - and ORIGINAL Stevens part for the mid- and later-production Favorites.

This is the front hanger with a slightly larger base for worn dove tail slots on the barrel. What can happen is if you don't know that the...

Magazine locking pin spring. This spring fits into either the model 1897 or model 12 shotgun magazine locking pin.

This is a NEW magazine spring for the Winchester 1866/1873/1894/ 1892 rifle. It fits the .38 and .44 cal in the 1873 and 1892 models. This...

This is the magazine spring Winchester 1886 lever action rifle. It is identicle to the 1876 spring and the same for all of the calibers. rifle the...

This is the hammer spring (mainspring), also called the mainspring Winchester model 1886. It lacks the hole mainspring screw unlike other models and...

This is an ORIGINAL hammer spring, also called the mainspring for the Winchester rifle. It fits the Winchester model 1866, 1876, and 1886; ALL...

hammer spring (mainspring) (also called the mainspring) that mounts on the lower tang and hammer stirrup. This spring provides the energy hammer to...

Mainspring plunger (seat) bracket fits late 1915 Favorite, Stevens Model 70, Ideal  NEW

Mainspring plunger fits the late 1915 Favorite.  This is an ORIGINAL part

Mainspring Screw Stevens model 70 NEW.  This part also was used in the late Stevens Favorite rifles (e.g., Model 1915 Favorites)

This screw holds the main spring (hammer spring (mainspring)) in place. The screw goes through the lower tang and is attached to the anterior portion...

NEW Mainspring Stevens Favorite flat spring with NO screw hole -- for early production 1889 and early 1894 Favorite rifles.  This spring has an...

NEW Mainspring Stevens Favorite flat spring with screw hole and raised tip -- for intermediate 1894  production Favorite rifles. See...

Mainspring Stevens Favorite flat spring with screw hole for later 1894 production rifles.  This is a NEW part. See the attached pdf diagram...

Mainspring ORIGINAL for the Stevens Ideal.  This spring fits into the receiver and is not attached with a retention screw.

Mainspring Stevens Favorite -- coil mainspring for later 1915 Fvorite production rifles, and also used in the Model 70 visible loader and Ideal...

This is the mainspring (also called hammer spring (mainspring)) Winchester 94 POST 64 rifle. It fits rifles with serial numbers 2,700,000-4,580,000....

This is a new operating sleeve spring Winchester model 63 and model 1903. It fits into the operating sleeve and around the bolt guide rod.

this is the spring that holds the safety bar into the lower tang on the Winchester model 94 POST 64.

This is the sear spring Winchester 1895

Trigger Lock Plunger Spring Winchester model 63 - 1903

Screw that holds the trigger spring in place on a Stevens Crackshot. This is an ORIGINAL part.  Also fits Crackshot, Ideal, late Favorite,...

This is the trigger spring Winchester model 61. It sits in a hole on the under side of the trigger.

This is an ORIGINAL style trigger spring for the Winchester model 63 and 1903 semiautomatic rifles.