OverSt

This is a discounted external screw set Winchester model 94 POST 64 Top eject Carbine. Your serial number should be from approximately 2,700,000 -...

This is the forearm screw also called the action slide handle screw. This screw that fits the model 62 and 62A and Model 1897 shotgun action slide...

Takedown (Assembly)replacement (NEW) screw for either a Winchester 1890 - 1906 - 62 - 62A pump 22 rifle. This secures receiver to the trigger...

This is the screw that holds on the rear barrel band on the Winchester model 94 POST 64 carbine rifle. It goes through the wooden forearm. NOTE ir...

These are the exact replicas of the large original style slot head buttplate screws crescent style and carbine style metal buttplates on the...

This is a white buttplate spacer that sits between the buttstock and the buttplate. On the option file below choose the size that closest matches...

This is the Carrier lever SPRING for Winchester models 1890, 1906, 62 and 62A Winchester (and Rossi) .22 pump rifle. This spring sits on top of the...

This is the screw that holds the carrier in place on the Winchester model 1895

This is the carrier Spring screw Winchester lever action model 1886 rifle. This screw hold on the carrier spring on the underside of the upper tang....

this is the cartridge guide screw Winchester 1886 lever action rifle. Will also fit the model 71 This screw holds on the cartridge guide on to the...

This is the cartridge guide screw Winchester 1894 and model 64 and model 55.

This is the dust cover (mortise cover) spring Winchester 1873. It is held in place by a screw (wp607A) in a rectangular cut out on the front of the...

Escutcheon for 1890 and 1906 Winchester pump handle. This part is blued metal. This will fit directly into the forearm and will keep the pump handle...

This extractor pin is used on the Winchester models 1890, 1906, 62 and 62A. It goes in to0 the top of the bolt on the right side and down...

Fits models 1894,64, 55 Winchester. This screw joins the finger lever to the link. (make sure when installing the head sits down in the counterbore...

This is the finger lever pin stop screw Winchester model 94 POST 64. The tip of this screw does not have threads on the Forearm. This screw is on the...

This is the pin that holds the finger lever into the receiver of the Winchester 1873 rifles. This pin goes through the receiver and finger lever and...

This is the forearm screw Winchester model 70 (pre 64)It goes into the forearm stud part number

This is the front guard screw Winchester model 70 pre 64.  Also called the magazine cover hinge polate screw.

This is the rear guard screw Winchester model 70 pre 64.

This is the pin that holds the hammer in place on the Winchester model 1873

This is the hammer screw Winchester model 1892 and 1894 and model 64 and model 55 . The hammer screw goes through the left side of the receiver...

This is the screw that holds the hammer in place on the Winchester model 94 POST 64

This is the link pin stop screw Winchester 1894 lever actin rifle and model 64 and model 55 . The tip of this screw presses into the groove on the...

This is the link screw Winchester model 94 POST 64. It fits top eject and angle eject below serial number 5,550,001

This is the screw that attaches the Loading gate (spring cover) to the receiver of the Winchester model 94 POST 64. It is used with all...

This is the pin the holds the magazine tight against the rear Magazine Hanger (magazine ring). It slides into a hole in the base of the rear mag...

This is the screw (short) that goes into the magazine plug on the Winchester 1873/1892/1894/1886/ 1866 and model 53 lever action rifles. If you have...

This is A NEW magazine plug screw Winchester model 12 all gauges

Spring that fits inside of the inner magazine tube on the Winchester 90 - 06 - 62 - 61 74. If you are able to get the magazine plug out by removing...

This is the screw that adjusts the tension on the hammer spring (mainspring) It is located in the middle of the lower tang. If your mainspring is...

This screw fits Winchester model 1892 - 1894 - 64 - 65 - 55 - 53. It is used to adjust the tension on the hammerspring (mainspring)

This is a STAINLESS STEEL plug screw 8-40 thread. These screws DO HAVE a little head on them and will not screw all the way through the receiver....

This saddle ring fits into the saddle ring stud or the U-shaped staple on the side of the model 1866, 1876, 1873, 1892, 1894 and 1895 Winchester...

Screw that holds side plate in place on 1890 and 1906 Winchester pump .22 rifles. This part fits model 90 or model 06 or 62A

This is the screw that holds on the sideplate Winchester 1876 lever action rifle

This is the type 2 sight elevator, also called sight step, Winchester .22 rifles. This elevator is blued. The highest adjustment point is .150...

This small screw raises and lowers the original rear sight 30-B on the 1890 and 1906 Winchester pump 22. It screws in just in front of the V-notch on...

This is the wood swivel stud that screws into forearm on rifles to attach sling to.

NEWLY ARRIVED! This is the wood screw lower tang on the Winchester 1866, 1873, 1876, 1886 and model 1885 rifle. It is located at the very back of the...

This is the screw that holds on the front of the Lyman and Marbles tang sight. It goes into the front hole (where the stock screw goes into the rear...

This is the trigger spring screw (Sear spring) - that fits the Winchester 1866, 1873, 1886, 1894, 1892, models 53, and 65. Also the 1890 1906 62 and...